Worth Data 802 RF Spécifications Page 4
- Page / 119
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1-1
Chapter 1
Installation
Components
The 802 Terminal is 802.11b compatible operating between 2399.5 MHz and 2474.5
MHz using direct sequence spread spectrum; it works with Access Points that are
802.11b or 802.11g compatible (b is a subset of g). The components in your 802
Terminal system will vary according to the configuration of your system. Your R/F
Terminal shipment should contain at least:
• An R/F Terminal T802 or LT802 (unit includes keypad and display).
If the R/F Terminal is an LT802 model, it will have an integrated laser
scanner built-in to the body of the terminal. Each terminal is shipped
with a shoulder strap, boot, and Manual.
• An optional Scanner – if you ordered the T802 models instead of the
LT802 models with the built-in laser scanner.
• Optional rechargeable batteries and a 9v power supply.
• 802 Utilities CD ROM – demo programs, Active X development
software, test program, and firmware loader program
Keep the shipping box for the R/F Terminal in the event it is necessary to
return equipment for repair later.
Installation Tips
1. Be sure all Access Points and Terminals have the same SSID and WEP
Key, (if Encryption is used). Terminals are shipped with a SSID of
WORTH DATA.
2. Start with one Terminal. Get everything working with the single
terminal and then add other terminals, being certain that all terminals
have unique IP Device Address.
3. Use the 802 Test Programs to validate that everything is working. If
you have problems, refer to the Trouble Shooting Section.
Using the RF Terminal keypad…
The R/F Terminal is turned on by pressing the green
ON/OFF button located in the upper left-hand corner
of the R/F Terminal keypad.
The R/F Terminal has a Shut Down Time feature that allows you to
determine the length of time the R/F Terminal must be inactive before
automatically shutting down to conserve battery power. When the R/F
- 802 RF Terminal Users Manual 1
- Table of Contents 2
- Installation 4
- R/F Terminal Menu Functions 7
- RF System Setup 10
- RF Terminal Setup Parameters 14
- SSID 15
- WEP Encryption Key 15
- Authentication 15
- Control Keys Only 15
- Backlight Duration 16
- Speaker 17
- 2 of 5 Code 21
- 2 of 5 Length 22
- MSI and Plessey 22
- RSS-14 23
- Code 93 23
- Beep Tone 23
- Batteries 23
- Date Format 24
- Set Date 24
- Set Time 24
- Display of Year 24
- Voice Message Partitions 25
- Shut Down Time 25
- Laser Scanner Options 25
- Aiming Dot Duration 26
- Reset 26
- Operational Theory 28
- Performance Issues 32
- Chapter 5 36
- Failure Planning 37
- Introduction 38
- Management 39
- WD802Term/ActiveX 41
- WD802Term uses port 54140 42
- WD802Term server 42
- Test For Good Communication 43
- Terminal Tracking 43
- Concepts – WD802Term ActiveX 44
- Methods – WD802Term ActiveX 46
- InputScanner 47
- InputYesNo 47
- InputPassword 47
- InputSerial 47
- InputMagStripe 47
- ReInitAll 50
- OutputRaw 50
- MapTermID 50
- GetIPAddress 50
- GetErrCode 50
- Events – WD802Term ActiveX 51
- OnTermNotSignedIn 52
- OnTermSequenceError 52
- OnTermIllegalCommand 52
- OnTermUpArrow 52
- OnTermDownArrow 52
- OnTermLeftArrow 53
- OnTermRightArrow 53
- OnTermBeginKey 53
- OnTermEndKey 53
- OnTermSearchKey 53
- Portable Printers 54
- Zebra QL 320 Printer 55
- Voice Message Operations 58
- Programming Voice Messages 59
- Default Voice Messages 61
- Terminal to 802 RF Terminal 61
- Troubleshooting 64
- Terminal Error Messages 66
- RF Terminal Problems 67
- Problems reading Bar Codes 68
- If you have a problem… 69
- Printer Pin-outs 70
- Firmware Upgrades 72
- Code 39 Specifications 74
- Mod 43 Check Character 75
- Accumulate Mode 77
- Code 93 Specifications 78
- Codabar Specifications 80
- Code 128 Specifications 82
- Interleaved 2 of 5 Code 84
- Specifications 84
- UPC / EAN Specifications 86
- Supplemental codes 87
- UPC-E Checksum Calculation 89
- MSI/Plessey Specifications 90
- How to scan a bar code 92
- Laser Options 93
- Using the Scan Stand 96
- Optional Features 98
- Laser Accessories 99
- T46 Holster for RF Terminal 100
- Rubber Boot for RF Terminal 101
- ASCII Code Equivalent Table 102
- 802 Display Character Code 104
- Mapping 104
- 802 RF Terminal Setup Menu 106
- *+X* *+Y* *+Z* *%P* 112
- *%Q* *%R* *%S* *%T* 112
- *+T* *+U* *+V* *+W* 112
Produits connexes et manuels pour Lecteurs de codes-barres Worth Data 802 RF
(126 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.319 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels